HUMZOR NEXZDAS ND366 ELITE
HUMZOR NEXZDAS ND366 ELITE
HUMZOR NEXZSYS NS366S IS PROFESSIONAL DIAGNOSTIC SCAN TOOLS, 4GBRAM, 64GB STORAGE, 10.1INCH HIGH DEFINITION TABLET, ANDROID VERSION 10, SUPPORT FULL SYSTEM DIAGNOSIS, KEY PROGRAMMING, SMART KEY PROGRAMMING, ECU CODING, ECU PROGRAMMING, ADAPTATION CALIBRATION, CODING, INITIALISATION, READ PIN CODE, PIN CODE CALCULATOR, WITH 13RESET FUNCTIONS, SAME AS NEXPEAK K1PLUS.
BETTER THAN LAUNCH CRP909E, THINKSCAN MAX, AUTEL MAXICOM MK808, MAXICHECK MX808.
NexzDAS ND366 Elite Supports Full OBD2 Functions
Read and Clear Codes:Read and clear engine codes. Stored, Pending and Permanent for all makes.
Live Data:DIY diversified PID display method(Graphic display, Dashboard display and Digital display). iOS supports 4 parameters comparison and Android supports 2.
Freeze Frame:Freeze Frame data is a snapshot of the vehicle when the Freeze Frame code was stored.
O2 Sensor:Check the vehicle O2 sensor values.
On Board Monitor Test (Mode 6): Advanced test results (like misfire counts) for on-board diagnostic system monitors.
Component Test (Mode 8):Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.
Battery Test：Show battery voltage and comment battery status.
Smog Check：Indicate whether or not the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
MIL Status :MIL is essentially an emission warning light. If the light comes on, it means the OBD II system has detected an emissions-related problem.
Vehicle Info：Check the make，years，VIN Code and other detail information of your Vehicle.
12 Special Functions + Key Programming
Note：These special functions are not for all car models, if you are confused, please send me your car model and we will check it for you.
Oil Reset：Allows you to perform reset maintenance mileage and data intervals for a new calculation of Engine Oil Life system once changed the oil.
TPMS：Makes tpms sensor in displaying sensor IDs from the vehicle’s ECU, inputting TPMS sensor replacement IDs and activate tpms sensors.
Injector Adjust：Diesel injector code need programming ID and parameters to the ECU for accurate communication and Injection control system.
EPB：It is important in the maintenance of electronic braking system’s safety and efficiency when replace brake pad or motor.
DPF :Specially works for Diesel Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.
TPS/ThrottleSensor:Vehicle’s throttle position system sensor connected to the butterfly spindle and is primarily used to monitor the throttle position within an inner combustion engine. Due to its location, the throttle position sensor is able to effectively observe where the throttle butterfly valve is positioned.
ABS Bleeding:The auto bleed procedure is used on BOSH 5.3 equipped vehicles. This procedure uses a scan tool to cycle the system solenoid valves and run the pump in order to purge the air from the secondary circuits.
SAS: Helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.
Battery Test:Allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the new battery replacement, and activate the rest state of the vehicle battery system
ØImmo Code Reading: Can read the Immo code of specific car models.
ØKey programming:Greatly supports key matching.
ØAdd car key: Add and match new key to the car.
ØErase car key:Delete the key that does not need.
ØKey information reading:Read the information of the key, quantity,frequency etc.
ØAll key lost:Support most cars all key lost via direct OBD matching.
Support 13 languages at present: English,Spanish, Italian, French, Russian, German, Polish, Japanese, Portuguese, Dutch, Hungarian, Chinese, Traditional Chinese. More are under developing, can up to 23 kinds.
Easy Operation Guide